chamfer是什么意思_chamfer怎么读_chamfer造句和翻译

chamfer

v.在…上雕槽[刻沟]；斜切；在…上挖圆槽

n.斜切面；削角

网络释义：倒角；倒直角；切角

网络释义

1.斜切面；削角a cut made along an edge or on a corner so that it slopes rather than being at 90˚

n.1.【机】圆角,倒角,倒棱,斜切2.槽,凹线;〈美〉圆槽3.斜面,切角面,棱角4.【建】削角1.【机】圆角,倒角,倒棱,斜切2.槽,凹线;〈美〉圆槽3.斜面,切角面,棱角4.【建】削角

v.1.在...上雕槽[刻沟]2.去...的角,斜切3.〈美〉(用圆凿)刳(木,石等),在...上挖圆槽

n.1.a shallow cut, edge, or groove made in wood, usually at an angle of 45 degrees to a corner

1.倒角 BR,*BREAK 打断 CHA,*CHAMFER 倒角 CO,*COPY 复制对象 ...

2.倒直角 CH,*PROPERTIES 属性框 CHA,*CHAMFER 倒直角 DCO,*DIMCONTINUE 连续标注 ...

3.切角 打断 break 切角 chamfer 倒角: fillet ...

4.倒斜角 03-23 ·螺纹- Modeling 03-23 ·倒斜角- chamfer 03-23 · 基准轴- Modeling Datum Axis ...

5.槽 Centipoises 厘泊（粘度单位） Chamfer 倒棱，槽 Chamfered joint 斜削接 ...

6.倒角命令 Centipoises 厘泊（粘度单位） Chamfer 倒棱，槽 Chamfered joint 斜削接 ...

1.Two chamfer disk milling cutters are arranged on a chamfer main shaft, and are separated by a separating bush to determine spacing.倒角主轴上装有两把倒角盘铣刀，通过隔套隔开并确定间距。

2.A milling hole main shaft, the chamfer main shaft and a main electric motor are all installed on a revolution body.铣孔主轴、倒角主轴和主电机均安装在回转体上。

3.The length of chamfer shall be between1 and2 complete threads as measured parallel to the axis of the threaded component.当平行于螺纹构件轴线方向进行测量时，倒角长度应该在1-2全螺纹扣之间。

4.Chamfer cap-there are all easy to wear, it is not easy out, and firmly strong and not easily lost or damaged.柱帽体有倒角容易戴入，不易拔出、牢固性强、不易丢失和破损。

5.To create a smooth transition select edges along connection of the wall and the floor and apply Chamfer.如果你要创建平滑的过渡，你可以沿着墙和地面交界的边，然后进行倒角。

6.A specially designed inner ring chamfer improves oil flow into the bearing for better lubrication and lower heat generation.有特别设计的内环倒角提高石油流入轴承进行更好的润滑和低热量的产生。

7.CHAMFER : The flat surface formed by cutting away the sharp edges of two meeting surfaces.倒角：两个表面相交处，通过切掉尖锐边缘形成的平面。

8.Diamond grade, thickness, chamfer, and or planar non-planar interface to your specifications.金刚石的粒度、厚度、倒角及界面是否平面，可以根据用户要求确定。

9.Clean facial ministry to had better breed character with chamfer, let corneous layer become soft, blain blain is squeezed more easily piece.清洗脸部最好用去角质乳，让角质层变得柔软，痘痘更轻易挤出。

10.rolling bearings . single - row angular contact ball bearings . chamfer dimensions for outer ring non - thrust side.滚动轴承。单列角面接触的球轴承。外圈非推力边的倒圆角尺寸。